HART

PROFIBUS PA

input

Measured variable

Gage pressure (flush-mounted)

Spans (infinitely adjustable) or
nominal measuring range and
max. pemissible test pressure

Measured span

Max. perm. test pressure

Nominal measuring range

Max. perm. test pressure

0.01 ... 1 bar g
(0.15 ... 14.5 psi g)

6 bar g
(87 psi g)

1 bar g
(14.5 psi g)

6 bar g
(87 psi g)

0.04 ... 4 bar g
(0.58 ... 58 psi g)

10 bar g
(145 psi g)

4 bar g
(58 psi g)

10 bar g
(145 psi g)

0.16 ... 16 bar g
(2.3 ... 232 psi g)

32 bar g
(464 psi g)

16 bar g
(232 psi g)

32 bar g
(464 psi g)

Depending on the process connection, the span may differ from these values

Depending on the process connection, the nominal measuring range may differ from these values

Lower measuring limit

• Measuring cell with silicone oil

100 mbar a (1.45 psi a)

Upper measuring limit

• Measuring cell with silicone oil

100 % of max. span

100 % of the max. nominal measuring range

Output

Output signal

4 ... 20 mA

Digital PROFIBUS PA signal

Physical bus

-

IEC 61158-2

With polarity reversal protection

No

Yes

Electrical damping T₆₃(step width 0.1 s)

Set to 0.1 s (0 ... 100 s)

Measuring accuracy

to EN 60770-1

Reference conditions

Increasing characteristic, start-of-scale value 0 bar, stainless steel seal diaphragm, measuring cell with silicone oil, room temperature 25 °C (77 °F), span ratio (r = max. span / set span)

Measurement deviation with cut-off point setting, including hysteresis and repeatability.

Linear characteristic curve

≤ 0.075 %

• r ≤ 10

≤ (0.0029 · r + 0.071)%

• 10 < r ≤ 30

≤ (0.0045 · r + 0.071)%

• 30 < r ≤ 100

≤ (0.005 · r + 0.05)%

Settling time T₆₃ without electrical damping

Approx. 0.2 s

Long-term drift at ±30 °C (±54 °F)

≤ (0.25 · r)%/5 years

≤ 0.25 %/5 years

Influence of ambient temperature

• at -10 ... +60 °C (14 ... 140 °F)

≤ (0.1 · r + 0.2)%

≤ 0.3 %

• at -40 ... -10 °C and +60 ... +85 °C
  (-40 ... 14 °F and 140 ... 185 °F)

≤ (0.1·r + 0.15) %/10 K

≤ 0.25 %/10 K

Influence of the medium temperature (only with front-flush diaphragm)

• Temperature difference between medium temperature and ambient temperature

3mbar/10 K (0.04 psi/10 K)

Rated conditions

Installation conditions

Ambient temperature

Observe the temperature class in areas subject to explosion hazard.

• Measuring cell with silicone oil

-40 ... +85 °C (-40 ... +185 °F)

• Digital display

-30 ... +85 °C (-22 ... +185 °F)

• Storage temperature

-50 ... +85 °C (-58 ... +185 °F)

Climatic category

Condensation

Permissible

Degree of protection to EN 60529

IP65, IP68, NEMA X, enclosure cleaning, resistant to lyes, steam to 150° C (302 °F)

Electromagnetic compatibility

• Emitted interference and noise immunity

To EN 61326 and NAMUR NE 21

Medium conditions

Temperature of medium

• Measuring cell with silicone oil

-40 ... +100 °C (-40 ... +212 °F)

Construction

Weight (without options)

Approx. 1 kg (2.2 lb)

Enclosure material

Stainless steel, mat. No. 1.4301/304

Material of parts in contact with the medium

• Seal diaphragm

Hastelloy C276, mat. No. 2.4819

• Measuring cell filling

Silicone oil

Power supply U_H

Terminal voltage on transmitter

10.5 ... 42 V DC
for intrinsically-safe operation: 10.5 ... 30 V DC

Supplied through bus

Separate power supply

-

Not necessary

Bus voltage

• Without EEx

-

9 ... 32 V

• For intrinsically-safe operation

-

9 ... 24 V

Current consumption

• Max. basic current

-

12.5 mA

• Startup current ≤ basic current

-

Yes

• Max. fault current in the event of a fault

-

15.5 mA

Fault disconnection electronics (FDE)

-

Available

Certificates and approvals

Classification according to pressure equipment directive (DRGL 97/23/EC)

For gases of fluid group 1 and liquids of fluid group 1; complies with requirements of Article 3, paragraph 3 (sound engineering practice)

Explosion protection

Intrinsic safety "i"

PTB 05 ATEX 2048

Identification

Ex II 1/2 G EEx ia/ib IIB/IIC T4, T5, T6

Permissible ambient temp.

• Temperature class T4

-40 ... +85 °C (-40 ... +185 °F)

• Temperature class T5

-40 ... +70 °C (-40 ... +158 °F)

• Temperature class T6

-40 ... +60 °C (-40 ... +140 °F)

Interface

To certified intrinsically-safe circuits with maximum values:

U_i = 30 V, I_i = 100 mA, 
P_i = 750 mW, R_i = 300 Ω

To certified intrinsically-safe circuits with maximum values:

FISCO supply unit:

U_i = 17.5 V, I_i = 380 mA, 
P_i = 5.32 W

Linear barrier:

U_i = 24 V, I_i = 250 mA, P_i = 1.2 W

Effective inner capacitance:

C_i = 6 nF

C_i = 1.1 nF

Effective inner inductance:

L_i = 0.4 mH

L_i ≤ 7 μH

Explosion protection to FM for USA and Canada (cFMUS)

• Identification (DIP) or (IS); (NI)

Certificate of Compliance 3025099

CL I, DIV 1, GP ABCD T4 ... T6; CL II, DIV 1, GP EFG; CL III; CL I, ZN 0/1 AEx ia IIC T4 ... T6; CL I, DIV 2, GP ABCD T4 ... T6; CL II, DIV 2, GP FG; CL III

• Identification (DIP) or (IS)

Certificate of Compliance 3025099C

CL I, DIV 1, GP ABCD T4 ... T6; CL II, DIV 1, GP EFG; CL III; Ex ia IIC 4 ... T6; CL I, DIV 2, GP ABCD T4 ... T6; CL II, DIV 2, GP FG; CL III

Simultaneous communication with master class 2 (max.)

4

The address can be set using

configuration tool

Local operation

(standard setting Address 126)

Cyclic data usage

• Output byte

One measuring value: 5 bytes

Two measuring values: 10 bytes

• Input byte

Register operating mode: 1 bytes

Reset function due to metering. 1 bytes

Device profile

PROFIBUS PA Profile for Process Control Devices Version 3.0, Class B

Function blocks

2

• Analog input

• Adaptation to customer-specific process variables

Linearly rising or falling characteristic

• Electrical damping T₆₃

0 ... 100 s adjustable

• Simulation function

Input /Output

• Limit monitoring

One upper and lower warning limit and one alarm limit respectively

• Register (totalizer)

Can be reset and preset

Optional direction of counting

Simulation function of the register output

• Limit monitoring

One upper and lower warning limit and one alarm limit respectively

• Physical block

1

Transducer blocks

2

• Pressure transducer block

• Monitoring of sensor limits

Yes

• Specification of a container characteristic with

Max. 31 nodes

• Characteristic

Linear

• Simulation function

Available

• Transducer block "Electronic temperature"

Simulation function

Available

HART

PROFIBUS PA or Foundation fieldbus

Input

Measured variable

Gage pressure

Spans (infinitely adjustable) or nominal measuring range and max. permissible test pressure

Span

Max. perm. test pressure

Nominal measuring range

Max. perm. test pressure

0.01 ... 1 bar g
(0.15 ... 14.5 psi g)

6 bar g
(87 psi g)

1 bar g
(14.5 psi g)

6 bar g
(87 psi g)

0.04 ... 4 bar g
(0.58 ... 58 psi g)

10 bar g
(145 psi g)

4 bar g
(58 psi g)

10 bar g
(145 psi g)

0.16 ... 16 bar g
(2.32 ... 232 psi g)

32 bar g
(464 psi g)

16 bar g
(232 psi g)

32 bar g
(464 psi g)

Lower measuring limit

Measuring cell with silicone oil filling

100 mbar a (1.45 psi a)

Upper measuring limit

100 % of max. span

Output

Output signal

4 ... 20 mA

Digital PROFIBUS PA or Foundation fieldbus signal

Lower limit (infinitely adjustable)

3.55 mA, factory preset to 3.84 mA

-

Upper limit (infinitely adjustable)

23 mA, factory preset to 20.5 mA or optionally set to 22.0 mA

-

Load

Without HART communication

R_B ≤ (U_H - 10.5 V)/0.023 A in Ω,
U_H : Power supply in V

-

With HART communication

R_B = 230 ... 500 Ω (SIMATIC PDM) or
R_B = 230 ... 1100 Ω (HART Communicator)

-

Physical bus

-

IEC 61158-2

With polarity reversal protection

-

Yes

Accuracy

Acc. to EN 60770-1

Reference conditions 
(All error data refer always refer to the set span)

Increasing characteristic, start-of-scale value 0 bar, stainless steel seal diaphragm, silicone oil filling, room temperature 25 °C (77 °F)) r: Span ratio 
(r = max. span / set span)

Error in measurement and fixed-point setting (including hysteresis and repeatability)

Linear characteristic

≤ 0.075 %

r ≤ 10

≤ (0.0029 · r + 0.071)%

10 < r ≤ 30

≤ (0.0045 · r + 0.071)%

30 < r ≤ 100

≤ (0.005 · r + 0.05)%

Long-term drift (temperature change ±30 °C (±54 °F))

≤ (0.25 · r)% every 5 years

≤ 0.25 % every 5 years

Influence of ambient temperature

at -10 ... +60 °C (14 ... 140 °F)

≤ (0.08 · r + 0.1)%

≤ 0.3 %

at -40 ... -10 °C and +60 ... +85 °C
(-40 ... +14 °F and 140 ... 185 °F)

≤ (0.1·r + 0.15) %/10 K

≤ 0.25 %/10 K

Influence of the medium temperature (only with flush-mounted diaphragm)

Temperature difference between medium temperature and ambient temperature

3 mbar/10 K (0.04 psi/10 K)

Influence of mounting position

≤ 0.1 mbar g (0.00145 psi g) per 10° inclination

Measured Value Resolution

-

3 · 10-5 of nominal measuring range

Rated operating conditions

Degree of protection (to EN 60529)

IP65, IP68, NEMA 4X, enclosure cleaning, resistant to lyes, steam to 150° C (302 °F)

Temperature of medium

-20 ... +100 °C (-4 ... +212 °F)

Ambient conditions

Ambient temperature

-20 ... +85 °C (-4 ... +185 °F)

Storage temperature

-50 ... +85 °C (-58 ... +185 °F)

Climatic class

Condensation

Permissible

Electromagnetic Compatibility

Emitted interference

Acc. to EN 50081-1

Interference immunity

Acc. to EN 61326 and NAMUR NE 21

Design

Weight (without options)

≈ 1.5 kg (≈ 3.3 lb)

Enclosure material

Low-copper die-cast aluminum GD-AlSi 12

Wetted parts materials

Gasket (standard)

PTFE flat gasket

O-ring (minibolt)

FPM (Viton) or optionally: FFPM or NBR

Measuring cell filling

Silicone oil or inert filling liquid

Process connection (standard)

Flush-mounted, 1½", PMC Standard design

Process connection (minibolt)

Flush-mounted, 1", minibolt design

Power supply U_H

Supplied through bus

Terminal voltage on transmitter

10.5 ... 45 V DC
10.5 ... 30 V DC in intrinsically-safe mode

-

Separate 24 V power supply necessary

-

No

Bus voltage

Not Ex

-

9 ...32 V

With intrinsically-safe operation

-

9 ...24 V

Current consumption

Basic current (max.)

-

12.5 mA

Startup current ≤ basic current

-

Yes

Max. current in event of fault

-

15.5 mA

Fault disconnection electronics (FDE) available

-

Yes

Certificates and approvals

Classification according to PED 97/23/EC

For gases of fluid group 1 and liquids of fluid group 1; complies with requirements of article 3, paragraph 3 (sound engineering practice)

Function blocks

3 function blocks analog input, 1 function block PID

• Analog input

• Adaptation to customer-specific process variables

Yes, linearly rising or falling characteristic

• Electrical damping T₆₃ , adjustable

0 to 100 s

• Simulation function

Output/input (can be locked within the device with a bridge)

• Failure mode

parameterizable (last good value, substitute value, incorrect value)

• Limit monitoring

Yes, one upper and lower warning limit and one alarm limit respectively

• Square-rooted characteristic for flow measurement

Yes

• PID

Standard FF function block

• Physical block

1 resource block

Transducer blocks

1 transducer block Pressure with calibration, 1 transducer block LCD

• Pressure transducer block

• Can be calibrated by applying two pressures

Yes

• Monitoring of sensor limits

Yes

• Simulation function: Measured pressure value, sensor temperature and electronics temperature

Constant value or over parameterizable ramp function

HART

PROFIBUS PA and FOUNDATION fieldbus

Gage pressure input

Measured variable

Gage pressure (flush-mounted)

Spans (infinitely adjustable) or nominal measuring range and
max. permissible test pressure

Measuring span

Max. perm. test pressure

Nominal measuring range

Max. perm. test pressure

0.01 ... 1 bar g
(0.15 ... 14.5 psi g)

6 bar g
(87 psi g)

1 bar g
(14.5 psi g)

6 bar g
(87 psi g)

0.04 ... 4 bar g
(0.58 ... 58 psi g)

10 bar g
(145 psi g)

4 bar g
(58 psi g)

10 bar g
(145 psi g)

0.16 ... 16 bar g
(2.3 ... 232 psi g)

32 bar g
(464 psi g)

16 bar g
(232 psi g)

32 bar g
(464 psi g)

0.6 ... 63 bar g
(9.1 ... 914 psi g)

100 bar g
(1450 psi g)

63 bar g
(914 psi g)

100 bar g
(1450 psi g)

1.6 ... 160 bar g
(23.2 ... 2321 psi g)

250 bar g
(3626 psi g)

160 bar g
(2321 psi g)

250 bar g
(3626 psi g)

4.0 ... 400 bar g
(58 ... 5802 psi g)

500 bar g
(7252 psi g)

400 bar g
(5802 psi g)

500 bar g
(7252 psi g)

Depending on the process connection, the span may differ from these values

Lower measuring limit

• Measuring cell with silicone oil

30 mbar a (0.44 psi a)

Upper measuring limit

• Measuring cell with silicone oil

100 % of max. span

100 % of the max. nominal measuring range

Absolute pressure input

Measured variable

Absolute pressure

Spans (infinitely adjustable) or nominal measuring range and
max. permissible test pressure

Measuring span

Max. perm. test pressure

Nominal measuring range

Max. perm. test pressure

8 ... 250 mbar a
(0.12 ... 3.6 psi a)

2 bar a
(29 psi a)

250 mbar a
(3.6 psi a)

2 bar a
(29 psi a)

0.043 ... 1.30 bar a
(0.62 ... 19 psi a)

10 bar a
(145 psi a)

1.30 bar a
(19 psi a)

10 bar a
(145 psi a)

0.16 ... 5 bar a
(2.3 ... 73 psi a)

30 bar a
(435 psi a)

5 bar a
(73 psi a)

30 bar a
(435 psi a)

1 ... 30 bar a
(14.5 ... 435 psi a)

100 bar a
(1450 psi a)

30 bar a
(435 psi a)

100 bar a
(1450 psi a)

Lower measuring limit

• Measuring cell with silicone oil

0 mbar a (0 psi a)

Upper measuring limit

• Measuring cell with silicone oil

100% of max. span

100 % of the max. nominal measuring range

Input of gage pressure, with flush-mounted diaphragm

Measured variable

Gage pressure (flush-mounted)

Spans (infinitely adjustable) or nominal measuring range and max. permissible test pressure

Measuring span

Max. perm. test pressure

Nominal measuring range

Max. perm. test pressure

0.01 ... 1 bar g (0.15 ... 14.5 psi g)

6 bar g
(87 psi g)

1 bar g
(14.5 psi g)

6 bar g
(87 psi g)

0.04 ... 4 bar g (0.58 ... 58 psi g)

10 bar g
(145 psi g)

4 bar g
(58 psi g)

10 bar g
(145 psi g)

0.16 ... 16 bar g (2.32 ... 232 psi g)

32 bar g
(464 psi g)

16 bar g
(232 psi g)

32 bar g
(464 psi g)

0.6 ... 63 bar g (9.14 ... 914 psi g)

100 bar g
(1450 psi g)

63 bar g
(914 psi g)

100 bar g
(1450 psi g)

Lower measuring limit

100 mbar a (0 psi a)

Upper measuring limit

• Measuring cell with silicone oil

100 % of max. span

100 % of the max. nominal measuring range

Input of absolute pressure, with flush-mounted diaphragm

Measured variable

Absolute pressure (flush-mounted)

Spans (infinitely adjustable) or nominal measuring range and
max. permissible test pressure

Measuring span

Max. perm. test pressure

Nominal measuring range

Max. perm. test pressure

43 ... 1300 mbar a
(0.62 ... 18.9 psi g)

10 bar a
(145 psi a)

1300 mbar a
(18.9 psi a)

10 bar a
(145 psi a)

0.16 ... 5 bar a
(2.32 ... 72.5 psi a)

30 bar a
(435 psi a)

5 bar a
(72.5 psi a)

30 bar a
(435 psi a)

1 ... 30 bar a
(14.5 ... 435 psi a)

100 bar a
(1450 psi a)

30 bar a
(435 psi a)

100 bar a
(1450 psi a)

Depending on the process connection, the span may differ from these values

Lower measuring limit

0 bar a (0 psi a)

Upper measuring limit

• Measuring cell with silicone oil

100% of max. span

100 % of the max. nominal measuring range

Output

Output signal

4 ... 20 mA

Digital PROFIBUS PA signal

Physical bus

-

IEC 61158-2

With polarity reversal protection

No

Yes

Electrical damping T₆₃ (step width 0.1 s)

Set to 0.1 s (0 ... 100 s)

Measuring accuracy

Reference conditions 
(All error data refer always refer to the set span)

Increasing characteristic, start-of-scale value 0 bar, stainless steel seal diaphragm, measuring cell with silicone oil, room temperature 25 °C (77 °F), span ratio (r = max. span / set span)

Measurement deviation with limit setting, including hysteresis and repeatability.

Gage pressure

Absolute pressure

Absolute pressure, flush-mounted

Gage pressure

Absolute pressure

Absolute pressure, flush-mounted

Linear characteristic

≤ 0.075 %

≤ 0.01 %

≤ 0.02 %

• r ≤ 10

≤ (0.0029 · r + 0.071)%

≤ 0.1 %

≤ 0.2 %

• 10 < r ≤ 30

≤ (0.0045 · r + 0.071)%

≤ 0.2 %

≤ 0.4 %

• 30 < r ≤ 100

≤ (0.005 · r + 0.05)%

-

-

Settling time T₆₃without electrical damping

Approx. 0.2 s

Long-term drift at ±30 °C (±54 °F)

≤ (0.25 · r)%/5 years

≤ (0.1 · r)%/year

≤ 0.25 %/5 years

≤ 0.1 %/year

Influence of ambient temperature

• at -10 ... +60 °C (14 ... 140 °F)

≤ (0.1 · r + 0.2)%

≤ (0.2 · r + 0.3)%

≤ 0.3 %

≤ 0.5 %

• at -40 ... -10 °C and +60 ... +85 °C
  (-40 ... 14 °F and 140 ... 185 °F)

≤ (0.1·r + 0.15) %/10 K

≤ (0.2·r + 0.3) %/10 K

≤ 0.25 %/10 K

≤ 0,5 %/10 K

Influence of the medium temperature (only with flush-mounted diaphragm)

• Temperature difference between medium temperature and ambient temperature

3 mbar/10 K (0.04 psi/10 K)

Conditions of use

Installation conditions

Ambient temperature

Observe the temperature class in areas subject to explosion hazard.

• Measuring cell with silicone oil

-40 ... +85 °C (-40 ... +185 °F)

• Measuring cell with Neobee oil (with flush-mounted diaphragm)

-10 ... +85 °C (14 ... +185 °F)

• Measuring cell with inert liquid (not with flush-mounted diaphragm)

-20 ... +85 °C (-4 ... +185 °F)

• Digital display

-30 ... +85 °C (-22 ... +185 °F)

• Storage temperature

-50 ... +85 °C (-58 ... +185 °F)
(for Neobee: -20 ... +85 °C (-4 ... +185 °F))

Climatic class

Condensation

Permissible

Degree of protection acc. to EN 60529

IP65, IP68, NEMA X, enclosure cleaning, resistant to lyes, steam to 150° C (302 °F)

Electromagnetic Compatibility

• Emitted interference and interference immunity

Acc. to EN 61326 and NAMUR NE 21

Medium conditions

Temperature of medium

• Measuring cell with silicone oil

-40 ... +100 °C (-40 ... +212 °F)

• Measuring cell with silicone oil (with flush-mounted diaphragm)

-40 ... +150 °C (-40 ... +302 °F)

• Measuring cell with Neobee oil (with flush-mounted diaphragm)

-10 ... +150 °C (-14 ... +302 °F)

• Measuring cell with silicone oil, with temperature decoupler (only with flush-mounted diaphragm)

-40 ... +200 °C (-40 ... +392 °F)

• Measuring cell with inert liquid

-20 ... +100 °C (-4 ... +212 °F)

• Measuring cell with high-temperature oil

-10 ... +250 °C (14 ... 482 °F)

Design (standard version)

Weight (without options)

Approx. 800 g (1.8 lb)

Enclosure material

Stainless steel, mat. No. 1.4301/304

Material of parts in contact with the medium

• Connection shank

Stainless steel, mat. No. 1.4404/316L or Hastelloy C276, mat. No. 2.4819

• Oval flange

Stainless steel, mat. No. 1.4404/316L

• Seal diaphr.

Stainless steel, mat. No. 1.4404/316L or Hastelloy C276, mat. No. 2.4819

• Measuring cell filling

• Silicone oil
• Inert filling liquid

Process connection

• G½B to EN 837-1
• Female thread ½-14 NPT
• Oval flange PN 160 (MWP 2320 psi) with fastening thread:
  • ⁷⁄₁₆-20 UNF to IEC 61518

• M10 as per DIN 19213

Design (version with flush-mounted diaphragm)

Weight (without options)

Approx. 1 … 13 kg (2.2 … 29 lb)

Enclosure material

Stainless steel, mat. No. 1.4301/304

Material of parts in contact with the medium

• Process connection

Stainless steel, mat. No. 1.4404/316L

• Seal diaphr.

Stainless steel, mat. No. 1.4404/316L

• Measuring cell filling

• Silicone oil
• Inert filling liquid
• FDA compliant fill fluid (Neobee oil)

Process connection

• Flanges as per EN and ASME
• F&B and pharmaceutical flanges

Power supply U_H

Terminal voltage on transmitter

10.5 ... 42 V DC
for intrinsically safe operation: 10.5 ... 30 V DC

Supplied through bus

Separate power supply

-

Not necessary

Bus voltage

• Without EEx

-

9 ... 32 V

• With intrinsically-safe operation

-

9 ... 24 V

Current consumption

• Max. basic current

-

12.5 mA

• Startup current ≤ basic current

-

Yes

• Max. fault current in the event of a fault

-

15.5 mA

Fault disconnection electronics (FDE)

-

Available

Certificates and approvals

Classification according to PED 97/23/EC

For gases of fluid group 1 and liquids of fluid group 1; complies with requirements of Article 3, paragraph 3 (sound engineering practice)

Water, waste water

In preparation

Explosion protection

Intrinsic safety "i"

PTB 05 ATEX 2048

Marking

Ex II 1/2 G EEx ia/ib IIB/IIC T4, T5, T6

Permissible ambient temperature

• Temperature class T4

-40 ... +85 °C (-40 ... +185 °F)

• Temperature class T5

-40 ... +70 °C (-40 ... +158 °F)

• Temperature class T6

-40 ... +60 °C (-40 ... +140 °F)

Interface

To certified intrinsically-safe circuits with maximum values:

U_i = 30 V, I_i = 100 mA, 
P_i = 750 mW, R_i = 300 Ω

To certified intrinsically-safe circuits with maximum values:

FISCO supply unit:

U_i = 17.5 V, I_i = 380 mA, 
P_i = 5.32 W

Linear barrier:

U_i = 24 V, I_i = 250 mA, P_i = 1.2 W

Effective inner capacitance:

C_i = 6 nF

C_i = 1.1 nF

Effective internal inductance:

L_i = 0.4 mH

L_i ≤ 7 μH

Explosion protection to FM for USA and_US)Canada (cFM

• Identification (DIP) or (IS); (NI)

Certificate of Compliance 3025099

CL I, DIV 1, GP ABCD T4 ... T6; CL II, DIV 1, GP EFG; CL III; CL I, ZN 0/1 AEx ia IIC T4 ... T6; CL I, DIV 2, GP ABCD T4 ... T6; CL II, DIV 2, GP FG; CL III

• Identification (DIP) or (IS)

Certificate of Compliance 3025099C

CL I, DIV 1, GP ABCD T4 ... T6; CL II, DIV 1, GP EFG; CL III; Ex ia IIC 4 ... T6; CL I, DIV 2, GP ABCD T4 ... T6; CL II, DIV 2, GP FG; CL III

Function blocks

3 function blocks analog input, 1 function block PID

• Analog input

• Adaptation to customer-specific process variables

Yes, linearly rising or falling characteristic

• Electrical damping T₆₃ , adjustable

0 to 100 s

• Simulation function

Output/input (can be locked within the device with a bridge)

• Failure mode

parameterizable (last good value, substitute value, incorrect value)

• Limit monitoring

Yes, one upper and lower warning limit and one alarm limit respectively

• Square-rooted characteristic for flow measurement

Yes

• PID

Standard FF function block

• Physical block

1 resource block

Transducer blocks

1 transducer block Pressure with calibration, 1 transducer block LCD

• Pressure transducer block

• Can be calibrated by applying two pressures

Yes

• Monitoring of sensor limits

Yes

• Simulation function: Measured pressure value, sensor temperature and electronics temperature

Constant value or over parameterizable ramp function

Pressure transmitters for food, pharmaceuticals and biotechnology

Mode of operation

Measuring principle

Piezo-resistive

Input

Measured variable

Gage or absolute pressure

Measuring range

0 ... 160 mbar (0 ... 2.32 psi)
... 
0 ... 40 bar (0 ... 580 psi)

Output

Output signal

• Two-wire system

4 ... 20 mA

• 3-wire system

0 ... 20 mA

Measuring accuracy

to EN 60770-1

Linearity error including hysteresis (reference point adjustment)

= 0.2 % of full-scale value

Adjustment accuracy

= ± 0.2 % of full-scale value

Response time

< 20 ms

Influence of ambient temperature

On the enclosure

• Zero

< 0.2 %/10 K of full-scale value

• Measured span

< 0.2 %/10 K of full-scale value

On the process connection (remote seals)

Zero error (depends on design)

• Flange remote seal

• DN 25 / 1"

4.8 mbar/10 K (0.070 psi/10 K)

• DN 32 / 1¼"

2.3 mbar/10 K (0.033 psi/10 K)

• DN 40 / 1½"

1.6 mbar/10 K (0.023 psi/10 K)

• DN 50 / 2"

0.6 mbar/10 K (0.009 psi/10 K)

• Clamp-on seal

• DN 25 / 1"

9.5 mbar/10 K (0.138 psi/10 K)

• DN 32 / 1¼"

4.1 mbar/10 K (0.060 psi/10 K)

• DN 40 / 1½"

3.9 mbar/10 K (0.057 psi/10 K)

• DN 50 / 2"

3.9 mbar/10 K (0.057 psi/10 K)

The zero error specified for the process connection should be considered as a guideline for a standard design. We will produce a detailed system calculation on request. Systems with reduced remote seal errors are available on request.

Rated conditions

Installation conditions

• Mounting position

Any, vertical as standard

Ambient conditions

• Ambient temperature

-10 ... +70 °C (14 ... 158 °F)

• Storage temperature

-10 ... +90 °C (14 ... 194 °F)

• Process temperature

Max. 200 °C (392 °F), depending on design

• Degree of protection (to EN 60529)

IP65, optional IP67

• Electromagnetic compatibility

• Emitted interference

To EN 50081 Part 1, issue 1993 (residential and industrial areas). The unit has no own emissions.

• Noise immunity to

EN 50082 Part 2, issue March 1995 (industrial areas)

Construction

Weight (without remote seal)

• Field housing

˜ 460 g (˜ 1.01 lb)

• Enclosure with plug

˜ 200 g (˜ 0.44 lb)

Enclosure

• Designs

• Field housing IP65 or IP67, with screwed gland
• Angled plug DIN 43650, IP65
• Cable connection, IP67
• Round plug connector M12, IP65

• Material

Stainless steel, mat. No. 1.4404/316L/1.4305

Material of union nut

Polyamide (with electrical connection using plug or cable)

Electronics unit potted with silicone

Internal ventilation for measuring ranges < 16 bar (< 232 psi), through housing thread or connecting cable depending on design

Process connection

• Versions

See ordering data

• Material of coupling

Stainless steel, mat. No. 1.4404/316L

Power supply

Terminal voltage on transmitter

10 ... 30 V DC

Rated voltage

24 V DC

Certificates and approvals

Classification according to pressure equipment directive (DRGL 97/23/EC)

For gases of fluid group 1 and liquids of fluid group 1; complies with the requirements of Article 3, paragraph 1 (appendix 1); assigned to category III, conformity evaluation module H by the TÜV Nord

Explosion protection

• Intrinsic safety "i"

TÜV 03 ATEX 2099 X

• Identification

Ex II 2G EEx ib IIC T6

SITRANS P pressure transmitters, ZD series

Mode of operation

Measuring principle

Thin-film strain gauge

Input

Measured variable

Gage and absolute pressure

Measured range

Resolution

0 ... 2 bar (0 ... 29 psi)

0.6 mbar (0.008 psi)

0 ... 10 bar (0 ... 145 psi)

3 mbar (0.044 psi)

0 ... 50 bar (0 ... 725 psi)

15 mbar (0.218 psi)

0 ... 200 bar (0 ... 2900 psi)

60 mbar (0.9 psi)

0 ... 400 bar (0 ... 5802 psi)

120 mbar (1.8 psi)

Measured range

Overload limit

0 ... 2 bar (0 ... 29 psi)

5 bar (72.5 psi)

0 ... 10 bar (0 ... 145 psi)

25 bar (363 psi)

0 ... 50 bar (0 ... 725 psi)

120 bar (1740 psi)

0 ... 200 bar (0 ... 2900 psi)

500 bar (7250 psi)

0 ... 400 bar (0 ... 5802 psi)

600 bar (8700 psi)

Range adjustment (turndown)

5:1 (max. 10:1)

Output

Output signal

4 ... 20 mA

Lower current limit

min. 3.6 mA

Upper current limit

max. 23 mA

Output protected against

Reversed polarity, overvoltage and short-circuiting

Max. load

R _B = (U_H - 12 V) / 0.023 A

Voltage measurement

Linear rising

Measuring accuracy

To EN 60770-1

Error in measurement (including non-linearity, hysteresis and repeatability, at 25 °C (77 °F))

< 0.25 % of full-scale value (typical), max. 0.5 %

Adjustment time

< 100 ms

Long-term drift

0.25 % of full scale value/year

Influence of ambient temperature

• Range adjustment 1:5

< ±0.25 %/10 K of full-scale value

• Range adjustment 1:10

±0.5 %/10 K of full-scale value

Vibration influence

0.05 %/g to 500 Hz in all directions (to IEC 68‑2‑64)

Power supply effect

< ±0.01 %/V of full-scale value

Rated conditions

Ambient conditions

• Ambient temperature

-25 ... +85 °C (-13 ... +185 °F)

• Temperature for best readability

-10 ... +70 °C (14 ... 158 °F)

• Storage temperature

-40 ... +85 °C (-40 ... +185 °F)

Medium conditions

• Process temperature

-30 ... +100 °C (-22 ... +212 °F)

Degree of protection

IP65 to EN 60529

Electromagnetic compatibility

• Emitted interference and noise immunity

To EN 61 326/A1 appendix A (1998)

Displays and controls

Display

LCD, max. 5 digits, digit height 9 mm

Decimal point

Freely parameterizable

Limit values

Freely parameterizable

Limit violation display

Red LED and message on LCD 
(↑symbol /↓symbol in case of limit violation in upward / downward direction)

Parameterization

With 3 keys

Units

mA or % or physical variable (default setting: bar)

Other dimensions: mbar, kPa, MPa, mmH₂0, mH₂0, psi, inH₂0, mmHg, kg/cm², torr, atm

Damping

Between 0.1 and 100 s

(increment: 0.1 s) freely parameterizable

Design

Weight

≈0.6 kg (≈1.32 lb)

Electrical connection

Using 2-pole plug connector with M16x1.5‑Cable inlet to EN 175301‑803A, plastic

Process connection

• Male thread G½B and female thread G¹/₈B
• G½B to EN 837-1
• Female thread: ½-14 NPT

Version of housing/process connection

• Radial (type A), can be swiveled by max. ±120° (α)

• Axial (type B), can be swiveled by max. ±360°

Material

Non-wetted parts materials

• Field housing

∅ 80 mm (3.15 inch), stainless steel mat. No. 1.4016

• Cover

Stainless steel, mat. No. 1.4016 with glass

Wetted parts materials

• Measuring cell

Al₂O₃

• Gasket

Viton

• Process connection

Stainless steel, mat. No. 1.4571/316Ti